There aresix key reasons why a systemBIOSwill no detect the presence of an internal difficult drive. Di sini is a list of them. They room not in any certain order, yet you have the right to follow these steps one through one to troubleshoot this problem:


Note:Sections3, 4,5 and also 6 pertain to computer or Mac systems. Sections1 and also 2pertain just to computer systems.

Anda sedang menonton: Cara instal windows 10 tanpa masuk bios

After verifying that yourATAorSATAport is collection to Auto-Detect or is enabled, if you uncover that her disk drive is not being detect (auto-detected) by the mechanism BIOS, try the adhering to steps to shot and isolate/troubleshoot the problem.


Most personal computers display screen a quick message about entering mechanism Setup shortly after the power is turned on. Mechanism Setup is tambahan called the "system BIOS" or occasionally the "CMOS Setup" - each is a surname for the very same thing.
For example, top top Dell equipment you will watch "F2=Setup" in the upper appropriate hand cornerduring the computerboot-up. This way to tekan ke bawah the F2 an essential to enter Setup (the BIOS).Different computer manufactures have different methods to get in Setup, therefore please inspect your system documentation because that specifics.
If your drive is no detected it may be due to the fact that it is turned off in system Setup. Part motherboard manufactures disable unused port in the BIOS through default. Girlfriend will need to enter the the BIOS setup in order come verify milik mereka current state.
When you add a second drive come the system, it may be need to be enabled by transforming it ~ above in system Setup.

Faulty orUnplugged Data CableAlways examine the motherboard and also hard disk connections for bend or misaligned pins. Folding, crimping, pinching, or creasing data cables can cause the wires to break inside the insulation, leave the exterior of the cable feather normal. As soon as in doubt that data cable condition, change it.The BIOS will certainly not recognize a difficult disk if the data cable is damaged or the link is incorrect. Serial ATA cables, in particular, have the right to sometimes autumn out of anda connection. Be certain to inspect your SATA cables room tightly linked to the SATA port connection.The easiest means to test a cable is to change it with lagi cable. If the difficulty persists, kemudian the cable was no the reason of the problem.For ATA drives, buycia2.com recommends lihat UDMA cabling with a maximum size of 18 inches. UDMA cables have color coded relationships which require ideal orientation as soon as connecting. Watch this image: (Click to expand)
*
Blue connector- selalu connects to the motherboard.Grey (middle) connector- is used for slave tools on the cable.Black connector - is digunakan for master device connection.

Drive is not spinning increase If the drive is not receiving power or receiving one incorrect level of power,it will not turn up. To examine to view if this is the reason of the BIOS no detecting the difficult drive, follow this steps:Power off the computer.Open the computer case and remove the data cable from the tough drive. This will certainly stop any type of power saving commands from being sent.Turn top top the system. Inspect to check out if the tough drive is spinning. If you touch thesideof the journey you should feel a slim vibration. If youdo nothear or feel the tough drive spinning, the drive did not start.


Boot the computer and listen carefully.Shut the computer down.Disconnect the strength cord native the computer system itself.Disconnect the power cable indigenous the hard drive in question.Reconnect the power cord to the computer itself.Boot the computer up to check out if the journey sound to be audible before. And,Then repeat, only reconnect the tough drive and also listen because that it to spin up.Switch strength cables with a an equipment like a CDROM or DVDROM drive, so the you are penampilan a known-good power cable.Check the strength supply on her computerto determine whether the is giving sufficient electric powerto run the drives and also devices you have actually in her computer.If the journey is still no spinning, attach it in lainnya computer if possible.Connect the drive in a SATA-USBenclosure or something comparable if possible.
ATA: that is recommended that all buycia2.com ATA difficult disks supporting the Cable Selectjumper option be configured together Cable Select. If your computer system was developed prior to October 1998 and melakukan not support UDMA 66 or lebih besar you will be forced to use the Master/Slave jumper settings.

Lihat lainnya: Latihan Contoh Soal Ukk Kelas 6 Sd Mi K13 Tahun 2021 Dan Kunci Jawabannya


-
*
-- (Click to expand) Jumper settings for buycia2.com ATA drives
-
*
-- (Click come expand) Jumper setups for Maxtor-brand ATA drives
When melihat Cable select jumper setups on her ATA drive, every devices associated to the UDMA cable must tambahan use the Cable choose setting. The cable decides master/slave an equipment detection as soon as the cable choose jumper setups are used.
Ifyouhave menyelesaikan the above checks and also procedures and the drive is still not effectively detected, please attempt come useSeaTools for DOS(seethe tutorial here) to check the drive. If SeaTools does not detect the journey after the steps adhered to above, oran error code that signifies drive failure displays,please continue to theour Warranty services pageto begin a warranty replacement order.